Change your pool temperature and timers from wherever you are
Pool heat pumps are very efficient, converting the power used and returning five times or more the energy as heat
Inverter technology heat pumps use up to 15-30% less power consumption when compared to a non-inverter heat pump
Ultra quiet and highest efficiency standard offers you excellent experience for all seasons
Easy to navigate LCD screen control allows you to easily adjust setting according to your preference.
Pool heat pumps are very efficient, converting the power used and returning five times or more the energy as heat.
This unit returns 25KW + in heat output for only 3.98KW of electricity input.(The heat output will rise along with the outside temperature). Another way of looking at it is, for every $1 of power input you get $5-$6+ of heat! This compares with resistance heaters, like your spa which may heat an element and return only 1kw of heat for every 1kw of electricity in, or only $1 of heat for every $1 you spend.
Heat pumps are also considerably cheaper to run than electric or gas heating saving you up to 75%, Solar heating tubes on your roof require a lot of plumbing to install, need a pump to run, can be unsightly and NEED THE SUN! You can run your Swimmax Pool Heat Pump 24/7 quietly and economically in the cold and without the sun! They will work in temperatures from -15 degrees c to + 43 degrees c.This Swimmax Pool Heat Pump is also quiet at 42 DB(a)
Just turn it on!
* cost to produce 1 Million BTU of Heat, comparison % & price will vary.
The pipe installation can be done by yourself if you are handy, or your local plumber. With 40mm High Pressure PVC pipe (class 12 - 50mm external) simply have your pool heat pump inlet and outlet connected to your pool filter system outlet and inlet, after your pool pump. Bypass valves as per diagram are required to balance water flow through the pool heat pump for optimum performance.
Then have an electrician install a Suitable power supply on its own circuit with RCD and turn it on!
Check our heat pump kit to complete your setup.
The unit will work properly in any desired location as long as the following three items are present:
The unit may be installed in virtually any outdoor location as long as the specified minimum distances to other objects are maintained (see drawing below). Please consult your installer for installation with an indoor pool. Installation in a windy location does not present any problem at all.
|(1) 25iPS Heat pump||x1|
|(2) Barrel unions||x2|
|(3) 10m wire cable - controller||x1|
|(4) Water drainage pipes||x2|
|(5) Draining Plugs||x2|
|(6) Anti-vibration feet||x4|
|(7) Winter Cover||x1|
Note: Our advice is general. This unit may not be suitable for your needs or use. Please inquire BEFORE purchase. No refunds given for incorrect purchase or change of mind.
|Performance at Air 28°C. Water 28°C. Humidity 80%|
|Input Power/ Heating Capacity||24-5.9 kW|
|Input Current/ Power consummation||4-0.37 kW|
|Performance at Air 24°C. Water 26°C. Humidity 70%|
|Input Power/ Heating Capacity||23.8-5.8 kW|
|Input Current/ Power consummation||3.98-0.37 kW|
|Performance at Air 15°C. Water 26°C. Humidity 70%|
|Input Power/ Heating Capacity||17.2-4.5 kW|
|Input Current/ Power consummation||3.74-0.63 kW|
|Compressor Type||Inverter compressor (GMCC Inverter)|
|Voltage / Power Supply||220~240V / 50Hz or 60Hz /1PH|
|Rate Current||17.7 A|
|Minimum Fuse||25Amp – Hard Wired|
|Max Pool Volume||110,000 L|
|Water Flow (m3/h)||8|
|Water Pressure||20 Kpa|
|Heat Exchanger||Twist-titanium tube in PVC|
|Fan Speed||450-650 RPM|
|Power Input of fan motor||35-130 W|
|Noise at 10m||≤46 dB(A)|
|Noise at 1m||42-58|
|Heating mode and Auto mode setting range||6-41℃|
|Cooling mode ℃ setting range||6-35 ℃|
|Net weight||128 kg|
|Gross weight||146 kg|
|Net dimension (mm)||1134 x 446 x 872|
|Packing dimension (mm)||1186 x 495 x 1011|
Not all items available at all locations. Payment is to be made prior to pick up, either by Credit card over the phone or Direct Deposit. (Please note PAYPAL not available for this service.)
Swimmax Products are backed by a (1) Year Onsite and (3) Year Manufacturer's Parts Warranty.
The warranty exceeds the consumer warranties and guarantees under Australian Consumer Law. Warranties are for the Original Owner in the Original location.
We aim to assist promptly and professionally. Your cooperation and patience will help us resolve your issue more quickly. In most instances we can resolve your concern without a site visit; most issues are resolved promptly with customer assistance.
When you call for service, please note that our customer service team cannot send a technician, without first following our “Trouble Shooting and Diagnosis” procedure.
We will require your assistance in the first instance to "Trouble Shoot" (This is to avoid you paying for an unnecessary service call fee charged by the service agent). This may involve sending us photos, adjusting settings, testing, and ensuring the unit has been installed and operated with best practice.
Before calling for service, please read all instructions carefully and ensure the item is correctly setup.
Please also ensure you have the following information, have confirmed the following, and can provide it.
Our customer service team may be unable to assist you further if you cannot provide the requested information.
The best solution to any product fault depends on the nature of the fault itself, and each fault will be given a solution to best solve your problem.